All-Digital Frequency Synthesizer in Deep-Submicron CMOS (Hardcover)
暫譯: 全數位頻率合成器於深亞微米CMOS中 (精裝版)

Description

A new and innovative paradigm for RF frequency synthesis and wireless transmitter design

Learn the techniques for designing and implementing an all-digital RF frequency synthesizer. In contrast to traditional RF techniques, this innovative book sets forth digitally intensive design techniques that lead the way to the development of low-cost, low-power, and highly integrated circuits for RF functions in deep submicron CMOS processes. Furthermore, the authors demonstrate how the architecture enables readers to integrate an RF front-end with the digital back-end onto a single silicon die using standard ASIC design flow.

Taking a bottom-up approach that progressively builds skills and knowledge, the book begins with an introduction to basic concepts of frequency synthesis and then guides the reader through an all-digital RF frequency synthesizer design:

• Chapter 2 presents a digitally controlled oscillator (DCO), which is the foundation of a novel architecture, and introduces a time-domain model used for analysis and VHDL simulation
• Chapter 3 adds a hierarchical layer of arithmetic abstraction to the DCO that makes it easier to operate algorithmically
• Chapter 4 builds a phase correction mechanism around the DCO such that the system's frequency drift or wander performance matches that of the stable external frequency reference
• Chapter 5 presents an application of the all-digital RF synthesizer
• Chapter 6 describes the behavioral modeling and simulation methodology used in design

The final chapter presents the implementation of a full transmitter and experimental results. The novel ideas presented here have been implemented and proven in two high-volume, commercial single-chip radios developed at Texas Instruments: Bluetooth and GSM.

While the focus of the book is on RF frequency synthesizer design, the techniques can be applied to the design of other digitally assisted analog circuits as well. This book is a must-read for students and engineers who want to learn a new paradigm for RF frequency synthesis and wireless transmitter design using digitally intensive design techniques.

 

Table of Contents

PREFACE.

1 INTRODUCTION.

1.1 Frequency Synthesis.

1.1.1 Noise in Oscillators.

1.1.2 Frequency Synthesis Techniques.

1.2 Frequency Synthesizer as an Integral Part of an RF Transceiver.

1.2.1 Transmitter.

1.2.2 Receiver.

1.2.3 Toward Direct Transmitter Modulation.

1.3 Frequency Synthesizers for Mobile Communications.

1.3.1 Integer-N PLL Architecture.

1.3.2 Fractional-N PLL Architecture.

1.3.3 Toward an All-Digital PLL Approach.

1.4 Implementation of an RF Synthesizer.

1.4.1 CMOS vs. Traditional RF Process Technologies.

1.4.2 Deep-Submicron CMOS.

1.4.3 Digitally Intensive Approach.

1.4.4 System Integration.

1.4.5 System Integration Challenges for Deep-Submicron CMOS.

2 DIGITALLY CONTROLLED OSCILLATOR.

2.1 Varactor in a Deep-Submicron CMOS Process.

2.2 Fully Digital Control of Oscillating Frequency.

2.3 LC Tank.

2.4 Oscillator Core.

2.5 Open-Loop Narrowband Digital-to-Frequency Conversion.

2.6 Example Implementation.

2.7 Time-Domain Mathematical Model of a DCO.

2.8 Summary.

3 NORMALIZED DCO.

3.1 Oscillator Transfer Function and Gain.

3.2 DCO Gain Estimation.

3.3 DCO Gain Normalization.

3.4 Principle of Synchronously Optimal DCO Tuning Word Retiming.

3.5 Time Dithering of DCO Tuning Input.

3.5.1 Oscillator Tune Time Dithering Principle.

3.5.2 Direct Time Dithering of Tuning Input.

3.5.3 Update Clock Dithering Scheme.

3.6 Implementation of PVT and Acquisition DCO Bits.

3.7 Implementation of Tracking DCO Bits

3.7.1 High-Speed Dithering of Fractional Varactors.

3.7.2 Dynamic Element Matching of Varactors.

3.7.3 DCO Varactor Rearrangement.

3.8 Time-Domain Model.

3.9 Summary.

4 ALL-DIGITAL PHASE-LOCKED LOOP.

4.1 Phase-Domain Operation.

4.2 Reference Clock Retiming.

4.3 Phase Detection.

4.3.1 Difference Mode of ADPLL Operation.

4.3.2 Integer-Domain Operation.

4.4 Modulo Arithmetic of the Reference and Variable Phases.

4.4.1 Variable-Phase Accumulator (PV Block).

4.5 Time-to-Digital Converter.

4.5.1 Frequency Reference Edge Estimation.

4.6 Fractional Error Estimator.

4.6.1 Fractional-Division Ratio Compensation.

4.6.2 TDC Resolution Effect on Estimated Frequency Resolution.

4.6.3 Active Removal of Fractional Spurs Through TDC (Optional).

4.7 Frequency Reference Retiming by a DCO Clock.

4.7.1 Sense Amplifier–Based Flip-Flop.

4.7.2 General Idea of Clock Retiming.

4.7.3 Implementation.

4.7.4 Time-Deferred Calculation of the Variable Phase (Optional).

4.8 Loop Gain Factor.

4.8.1 Phase-Error Dynamic Range.

4.9 Phase-Domain ADPLL Architecture.

4.9.1 Close-in Spurs Due to Injection Pulling.

4.10 PLL Frequency Response.

4.10.1 Conversion Between the s- and z-Domains.

4.11 Noise and Error Sources.

4.11.1 TDC Resolution Effect on Phase Noise.

4.11.2 Phase Noise Due to DCO SD Dithering.

4.12 Type II ADPLL.

4.12.1 PLL Frequency Response of a Type II Loop.

4.13 Higher-Order ADPLL.

4.13.1 PLL Stability Analysis.

4.14 Nonlinear Differential Term of an ADPLL.

4.14.1 Quality Monitoring of an RF Clock.

4.15 DCO Gain Estimation Using a PLL.

4.16 Gear Shifting of PLL Gain.

4.16.1 Autonomous Gear-Shifting Mechanism.

4.16.2 Extended Gear-Shifting Scheme with Zero-Phase Restart.

4.17 Edge Skipping Dithering Scheme (Optional).

4.18 Summary.

5 APPLICATION: ADPLL-BASED TRANSMITTER.

5.1 Direct Frequency Modulation of a DCO.

5.1.1 Discrete-Time Frequency Modulation.

5.1.2 Hybrid of Predictive/Closed PLL Operation.

5.1.3 Effect of FREF/CKR Clock Misalignment.

5.2 Just-in-Time DCO Gain Calculation.

5.3 GFSK Pulse Shaping of Transmitter Data.

5.3.1 Interpolative Filter Operation.

5.4 Power Amplifier.

5.5 Digital Amplitude Modulation.

5.5.1 Discrete Pulse-Slimming Control.

5.5.2 Regulation of Transmitting Power.

5.5.3 Tuning Word Adjustment.

5.5.4 Fully Digital Amplitude Control.

5.6 Going Forward: Polar Transmitter.

5.6.1 Generic Modulator.

5.6.2 Polar TX Realization.

5.7 Summary.

6 BEHAVIORAL MODELING AND SIMULATION.

6.1 Simulation Methodology.

6.2 Digital Blocks.

6.3 Support of Digital Stream Processing.

6.4 Random Number Generator.

6.5 Time-Domain Modeling of DCO Phase Noise.

6.5.1 Modeling Oscillator Jitter.

6.5.2 Modeling Oscillator Wander.

6.5.3 Modeling Oscillator Flicker (1/f ) Noise.

6.5.4 Clock Edge Divider Effects.

6.5.5 VHDL Model Realization of a DCO.

6.5.6 Support of Physical KDCO.

6.6 Modeling Metastability in Flip-Flops.

6.7 Simulation Results.

6.7.1 Time-Domain Simulations.

6.7.2 Frequency-Deviation Simulations.

6.7.3 Phase-Domain Simulations of Transmitters.

6.7.4 Synthesizer Phase-Noise Simulations.

6.8 Summary.

7 IMPLEMENTATION AND EXPERIMENTAL RESULTS.

7.1 DSP and Its RF Interface to DRP.

7.2 Transmitter Core Implementation.

7.3 IC Chip.

7.4 Evaluation Board.

7.5 Measurement Equipment.

7.6 GFSK Transmitter Performance.

7.7 Synthesizer Performance.

7.8 Synthesizer Switching Transients.

7.9 DSP-Driven Modulation.

7.10 Performance Summary.

7.11 Summary.

APPENDIX A: SPURS DUE TO DCO SWITCHING.

A.1 Spurs Due to DCO Modulation.

APPENDIX B: GAUSSIAN PULSE-SHAPING FILTER.

APPENDIX C: VHDL SOURCE CODE.

C.1 DCO Level 2.

C.2 Period-Controlled Oscillator.

C.3 Tactical Flip-Flop.

C.4 TDC Pseudo-Thermometer Output Decoder.

REFERENCES.

INDEX.